Pentru mai multe informatii accesati urmatoarele link-uri:
1. MaxAir® Dryers
2. LaserH2O® Reverse Osmosis System
1. MaxAir® Dryers
MaxAir dries vehicles better than ever, yet uses less energy than conventional dryers.
PDQ’s MaxAir Drying Systems are a breakthrough in dryer performance. MaxAir dries vehicles better than ever, yet uses less energy than conventional dryers.
The key to MaxAir is optimizing air velocity and flow. As air exits a dryer, it travels at a high rate of speed or air velocity. The stream loses much of its speed as it meets the resistance of the surrounding air. By the time it reaches the vehicle, airflow has been minimized. In effect, optimum airflow is best near the dryer outlet. Unfortunately, that’s not where it’s needed. Through innovative design, MaxAir Dryers delivers high-velocity air to the vehicle surface – where it’s most important.
Your customers will enjoy drier vehicles – you’ll enjoy lower operating costs! Add MaxAir to your vehicle wash system today!
Information contained herein subject to change without notice.
MaxAir Stand Alone Drying Systems
The MaxAir Stand-Alone Dryer utilizes concentrated air columns, air drafting, and an optimized array of blowers to deliver high-velocity air to the vehicle surface.
Concentrated Air Columns
MaxAir maximizes air velocity to the vehicle surface by using concentrated air columns. You see examples of this principle in action every day. To make a garden hose more effective, you concentrate the water flow to increase water impact. To make a flashlight brighter, you concentrate the light beam. The same concept applies to MaxAir. Concentrated air columns are achieved by using round discharging nozzles at the bottom of the dryer outlet. Round nozzles are more effective than square or rectangular ones. Nozzles that are not round tend to break up the airflow, causing more of the air to disperse and lose velocity as it travels through the surrounding air. By concentrating the air columns, MaxAir delivers high-velocity air to the vehicle surface – whether it’s a tall SUV or low profile sports car.
MaxAir utilizes four stationary 7.5 horsepower blowers with the two center blowers in line to take advantage of air drafting. Drafting is a technique used by racecar drivers that literally splits the air. However, drafting is not limited to the world of motor sports. MaxAir also employs the technique. The first blower does the job of breaking the air, reducing the amount of wind resistance the trailing blower experiences. The trailing blower can now work on evaporating water off the vehicle surface. Optional 7.5hp side producers can be added to increase drying effectiveness even further.
MaxAir blowers are strategically positioned to move water quickly off the vehicle surface using the shortest distance possible. When water droplets move on a vehicle, they split. The more they split, the smaller they become. Unfortunately, smaller water droplets are more difficult to move. With MaxAir, large water droplets move quickly off the vehicle sides rather than up and over the vehicle.
MaxAir Integrated Drying System
PDQ’s MaxAir Integrated Drying System takes all the features of the stand alone system and tightly integrates them into the bridge or gantry of the car wash. Integrated dryers also can perform a unique FlashDry® service, taking no additional time for a basic dry, by performing a rinse and dry in a single operation. Developed on the simple theory that it is easier to remove water that is already moving – FlashDry improves rinsing while removing over 80% of the water all in a single 10 second pass. Options and variety in drying allow greater package differentiation that increases your revenue per car.
SwingAir Synchronized Motion Drying System
Your customers will enjoy drier vehicles with PDQ’s new SwingAir Synchronized Motion Drying System. The enhanced SwingAir oscillating feature improves dryer performance while still using less energy than most conventional dryers. This new system incorporates motion in the center two producers to help sweep water off of the vehicle’s top surface, allowing the two outside producers to focus on pushing water down and off the sides of the vehicle. The SwingAir feature is available on both stand-alone and integrated MaxAir Drying Systems and can be ordered on new car wash equipment as well as added as a retrofit kit for existing ProTouch® Tandem, Laserwash® 360 or MaxAir® stand-alone sites.
- Oscillating feature to sweep water from the surface of vehicles
- 32″ (81cm) wider drying envelope with repositioned outside producers
- Better drying on sides of vehicles with inward-angled outside producers
- Can be ordered with new wash systems or as a retrofit kit
- Available on six producer, four producer or two producer MaxAir systems
Brochures & Videos
40% less reject generated as compared to competing systems.
Isn’t it time you stopped wasting water?
The LaserH2O® Reverse Osmosis (RO) Systems are complete, electronically controlled, skid-mounted units that incorporate all of the water pretreatment operations necessary to ensure high-quality product water. The low-pressure, high-efficiency design provides an industry-leading water recovery of 70%. With no operational adjustments necessary due to the unique auto-adjusting flow-control system, the units are hassle-free. The units simply plug into a standard dedicated 115V, 20A wall outlet.
Most RO systems look alike, cost alike and perform alike. Once a system is in place, it seldom is scrutinized to see whether it continues to meet an operator’s requirements, or how it results in lower overall cost in the long run when it is treated as a commodity item. Recurring problems, membrane fouling, part replacements, frequent cleaning and general maintenance increase the hidden cost of operation. Water quality is extremely important to the car wash process and, above all, the availability of a water-quality system is even more crucial. In the ultimate analysis, an operator can pay a lot more than just the initial purchase price to keep an RO system functioning as intended.
Recognizing these issues, PDQ configured a robust and well-proven design for the LaserH2O RO System. This system utilizes an ultra high-efficiency membranetechnology that allows the use of super-low-horsepower pumps, thereby making its operation more efficient. The unit is mounted on a durable powder-coated steel structure with 115V electrical service to ensure simple installation. It does not require a separate pretreatment unit; instead it utilizes unique 2-in-1 media and carbon filters that can treat up to 70,000 gallons each. An antiscalant injection system is also available for areas where water hardness exceeds 150 mg/l (9 grains). PDQ’s LaserH2O system also operates at up to 70% recovery, meaning less wastewater, and is available in three sizes of 3000, 5000 and 7000 gallons per day of spot-free product water.
- Can produce 10 gallons of Spot Free from only 14.28 gallons of feed water
- 1000 gallons of Spot Free uses only 5.3kWh of electricity
- Plugs into standard 115V outlet
- Self-adjusting flow-control
- No water softener resin required (if below 24 grains)
- Less feed water consumption means less money wasted
- Lower operating pressure means longer system life
- Available in three sizes: 3000, 5000, & 7000 gallons per day
- Download the Brochure for more detailed specs
Information contained herein subject to change without notice. Savings are site specific and dependent on inlet TDS and other factors.
Why choose the PDQ LaserH2O® RO System? Here are 11 good reasons:
- 98% Salt Rejection
Membranes reject 98% salt content of the influent feed water.
- Higher Throughput at Lower Pressure
This translates directly into electricity savings – up to $1600 per year.
- 70% System Recovery
For every 10 gallons of spot free our system makes, only 4.28 gallons of waste water is generated. Competing systems generate 10 gallons of waste water for every 10 gallons of spot free, which is more money down the drain.
- No Water Softener Required
Our systems do not need a softener if water hardness is below 400 mg/l (24 grains). Anti-scalant is required for hardness levels between 150-400 mg/l (9-24 grains).
- Single Phase Connection
Plugs into a standard wall socket (115V, 20A).
- Non-Corrosive Housings for Membranes
Well proven in the field. PVC is durable against chloride attack, thereby eliminating problems of rust formation.
- Built-In Reject Recycle
Flushing of the membrane happens after the system is shut down. This procedure keeps the membranes cleaner and prolongs their life.
- Self-Regulating Orifice
Controls output and avoids the use of excessive instrumentation such as fluid controls on the discharge line.
- Very Little Instrumentation
Less to manage, less to go wrong.
- Packaged Delivery
Transportation charges for RO systems shipped separately range from $400-500. Shipping from one source eliminates this cost.
- Superior Design
Durable skid-mounted, powder-coated steel structure with 115V electrical service.
LaserJuice® – the best chemistry for PDQ touch-free equipment
(not available in North America).
The PDQ LaserJuice® System – A series of engineered wash solutions developed and marketed exclusively for the PDQ LaserJet™ and LaserWash® 360 systems. Built from a five year program searching for the best chemistry for touchless cleaning that offered superior performance that was safe for vehicles, operators and the environment.
LaserJuice chemicals are scaleable to meet your needs. You may choose to use just the LaserJuice 23 Base Cleaner and the LaserJuice 73 Gloss Finish products. Alternatively, we now offer a family of products designed to provide additional services to your customers and ultimately additional revenues to you. LaserJuice 11 Bug Softener, LaserJuice 15 Wheel Cleaner, or LaserJuice 18 Underbody Armor are only a few of the new products designed to help you produce a superior product for your customers – A Clean Shiny Dry Car.
LaserJuice not available in North America. Information contained herein subject to change without notice.
- Environmentally friendly.
- Cutting edge detergents manufactured through formulations that place considerable attention on man and low environmental impact.
- Cleaning surfactants are naturally derived and biodegradable – No synthetic chemicals are used.
- Industry leading product safety – listed as “irritant” only while most car wash cleaning solutions are “corrosive”.
- Meets and exceeds most municipal waste stream requirements meaning no additional equipment or processes are needed.
- All products comply with Regulation 1907/2006 (REACH).
- Packaged in easy to handle and transport 20 Kg containers.
A Partnership of Success
Revello was founded in 1984 by Mauro Revello. He dedicated the business exclusively to the carwash sector focusing on the automatic carwash. Revello succeeded by offering innovative new detergents and cutting edge formulations that place considerable attention on man and low environmental impact. PDQ Manufacturing witnessed the success Mr. Revello was having using his specialized detergents with our state of the art PDQ Laser Jet and LaserWash 360 product lines and immediately saw an opportunity to partner with Revello. We feel that with the size and support of PDQ Manufacturing and the specialized technologies of Revello, the cleaning results are second to none. Together we can help you produce a CLEAN, SHINY, DRY vehicle.
LaserJuice 23 Base Cleaner
A high performance single step cleaning solution that combines all natural biodegradable ingredients into a highly engineered formulation that optimizes cleaning in a PDQ LaserJet or LaserWash touch-free system. Initially developed for PDQ touch-free systems in Europe, the product offers the safest chemistry for the vehicle, the equipment, the operator and the environment.
- Single step application engineered to provide performance that competitors are not able to achieve using slower two step applications.
- Unique “stay wet” foaming action allows the product to continue to work on the surface for up to 30 seconds after application. Dirt can be seen running from the vehicle as the product loosens and binds itself to the soil for easy high pressure removal.
- Hard water tolerance provides no reduction in effectiveness up to 250 ppm (25 French degrees). This often reduces the need for water softening equipment.
LaserJuice 73 Gloss Finish
Developed to maximize the vehicle shine for the vehicle as consumers often connect shine to clean and a valuable wash experience. The quick applying product creates a non-oily sealant layer that effectively repels water and aids in drying.
- Immediate vehicle surface “adhesion” – no need for product dwell.
- All naturally derived and biodegradable ingredients. No synthetic chemicals are used.
- Easy to rinse application helps improve effectiveness of final fresh water or spot free rinsing services.
- Colorless on the vehicle and non-staining.
LaserJuice Family of Products
LaserJuice 11 Bug Softener
Detergent for the complete removal of insects from the body and windshield.
LaserJuice 15 Wheel Cleaner
Rim cleaner used during the winter in self-jet car washes. It removes heavy dirt and deposits from the rims and the lower part of the body.
LaserJuice 18 Underbody
Underbody protectant protects the vehicle from rust.
LaserJuice 42 Sharp Cleaner
Sharp cleaner provides a cleaning “boost” in difficult cleaning situations.
LaserJuice 57 Foaming Conditioner
Colored foaming detergent with snow effect, suitable for foam systems in car wash facilities. Available in Blue, Red and Yellow.
LaserJuice 62 Gloss Polish
Foam product suitable for polishing systems in car wash facilities. The wax effect is very bright and protective for the body and prevents the formation of rust on the unpainted or peeling parts. Facilitates the flow of drops in case of rain.
LaserJuice 78 Super Armor
The ultimate protectant. Provides long lasting protection for your vehicles.
LaserJuice 82 Beading Rinse
Self-drying waterproof wax for car wash facilities. Fast drying and extra-shiny, it prevents the formation of stains and spots.